He Fab-generated densities appeared along the interior of the filaments but

He Fab-generated densities appeared along the interior of the filaments but not on the outer edges, unlike kinesin-1 which generates characteristic motor density projections along the filament edges (Figure 2D), giving the first indication that the Fab fragments were localizing in the microtubule lumen. To confirm this observation and directly determine the Fab fragment binding site, we MedChemExpress UKI 1 visualized Fabdecorated acetylated microtubules by cryo-EM (Figure S2). The power spectra revealed an additional layerline at 1/8 nm (Figure S3B), indicative of regular Fab decoration with 8 nm spacing. 3D helical reconstructions of selected Fab-decorated acetylated microtubules showed significant density within the microtubule lumen (Figure 2F) that is not observed in unlabeled microtubules (Figure 2E) suggesting that these densities correspond to the Fab fragments. The Fab density follows a helical path with an 8 nm pitch (Figure 2F), revealing attachment to a single a-tubulin subunit of the ab-tubulin heterodimer.As a control, we employed cryo-EM and helical reconstructions of microtubules polymerized from completely deacetylated tubulins (SIRT2-treated) and decorated with the same preparation of Fab fragments. Surprisingly, similar densities with the same 8 nm spacing, attributed to Fab, were observed in the lumen of the deacetylated microtubules by both negative stain (Figure 2C) and cryo-EM (Figure 2G). The Fab bound to deacetylated microtubules at lower occupancy than that observed for the acetylated microtubule reconstruction, presumably due to a decreased affinity and/or the presence of unacetylated subunits in the deacetylated tubulin population. Because of the lower Fab occupancy, the corresponding densities appear smaller when shown at comparable thresholds to the 3D maps of Fab-labeled acetylated microtubules. However, adjusting the visible density threshold to lower cut-off levels reveals that the Fab densities establish a connectivity to tubulin that is similar to that observed in the case of acetylated microtubules (data not shown). These results provide the first definitive demonstration that the 6-11B-1 Fab fragment recognizes a K40 epitope that is localized in the microtubule lumen.Luminal K40-acetylation does not influence kinesin-1 binding on the microtubule surfaceThe localization of the K40 acetylation site in the microtubule lumen raises the important question of whether a luminal modification can directly influence motors and MAPs on the microtubule surface. The use of MEC-17 and SIRT2 enzymes toCryo-EM Localization of Acetyl-K40 on Microtubulesgenerate tubulin species that differ only in the K40 acetylation state allowed us to address this question with respect to the interaction of kinesin-1 motors with microtubules. When constitutively active forms of kinesin-1 motors were mixed with acetylated or deacetylated microtubules in the presence of AMPPNP (a non-hydrolyzable analogue of ATP), no differences were observed in the ability of the kinesin-1 motors to cosediment with acetylated or deacetylated microtubules (Figure 3). 16574785 These results indicate that the single K40 modification in the microtubule lumen is not Bexagliflozin site sufficient to alter the binding of kinesin-1 to the microtubule surface.The 6-11B-1 antibody recognizes both acetylated and deacetylated microtubulesThe fact that the 6-11B-1 Fab fragment decorated both acetylated and deacetylated microtubules was not anticipated. The 6-11B-1 antibody has been widely used to identify and l.He Fab-generated densities appeared along the interior of the filaments but not on the outer edges, unlike kinesin-1 which generates characteristic motor density projections along the filament edges (Figure 2D), giving the first indication that the Fab fragments were localizing in the microtubule lumen. To confirm this observation and directly determine the Fab fragment binding site, we visualized Fabdecorated acetylated microtubules by cryo-EM (Figure S2). The power spectra revealed an additional layerline at 1/8 nm (Figure S3B), indicative of regular Fab decoration with 8 nm spacing. 3D helical reconstructions of selected Fab-decorated acetylated microtubules showed significant density within the microtubule lumen (Figure 2F) that is not observed in unlabeled microtubules (Figure 2E) suggesting that these densities correspond to the Fab fragments. The Fab density follows a helical path with an 8 nm pitch (Figure 2F), revealing attachment to a single a-tubulin subunit of the ab-tubulin heterodimer.As a control, we employed cryo-EM and helical reconstructions of microtubules polymerized from completely deacetylated tubulins (SIRT2-treated) and decorated with the same preparation of Fab fragments. Surprisingly, similar densities with the same 8 nm spacing, attributed to Fab, were observed in the lumen of the deacetylated microtubules by both negative stain (Figure 2C) and cryo-EM (Figure 2G). The Fab bound to deacetylated microtubules at lower occupancy than that observed for the acetylated microtubule reconstruction, presumably due to a decreased affinity and/or the presence of unacetylated subunits in the deacetylated tubulin population. Because of the lower Fab occupancy, the corresponding densities appear smaller when shown at comparable thresholds to the 3D maps of Fab-labeled acetylated microtubules. However, adjusting the visible density threshold to lower cut-off levels reveals that the Fab densities establish a connectivity to tubulin that is similar to that observed in the case of acetylated microtubules (data not shown). These results provide the first definitive demonstration that the 6-11B-1 Fab fragment recognizes a K40 epitope that is localized in the microtubule lumen.Luminal K40-acetylation does not influence kinesin-1 binding on the microtubule surfaceThe localization of the K40 acetylation site in the microtubule lumen raises the important question of whether a luminal modification can directly influence motors and MAPs on the microtubule surface. The use of MEC-17 and SIRT2 enzymes toCryo-EM Localization of Acetyl-K40 on Microtubulesgenerate tubulin species that differ only in the K40 acetylation state allowed us to address this question with respect to the interaction of kinesin-1 motors with microtubules. When constitutively active forms of kinesin-1 motors were mixed with acetylated or deacetylated microtubules in the presence of AMPPNP (a non-hydrolyzable analogue of ATP), no differences were observed in the ability of the kinesin-1 motors to cosediment with acetylated or deacetylated microtubules (Figure 3). 16574785 These results indicate that the single K40 modification in the microtubule lumen is not sufficient to alter the binding of kinesin-1 to the microtubule surface.The 6-11B-1 antibody recognizes both acetylated and deacetylated microtubulesThe fact that the 6-11B-1 Fab fragment decorated both acetylated and deacetylated microtubules was not anticipated. The 6-11B-1 antibody has been widely used to identify and l.